When servicing Aplus units, what electrical components must be checked and tightened if necessary?
Aplus Franchise · 2024 FDDAnswer from 2024 FDD Document
ATION | Phone Number | | Current Bank Name | | | | Current Last 4 Digits of Bank Account Number | Customer Authorization – Signature need to be hand signed, DocuSign or electronically verifiable with a date and time stamp | Current Bank Transit / ABA No. | | | | | | Authorized Signature | Printed Name | | | Date | Tax ID Number | Social Security Number |# INSURANCE COVERAGE REQUIREMENTS
| Annual Service Call Frequency | 3X | |---|---| | Compressor Maintenance (Basic) | | | Visually check for leaks. | X | | Check and record suction & discharge pressure, oil pressure, room & ambient | X | | temperature. | | | Air Handling Unit (AHU) Maintenance (Basic) | | | Install standard filters | X | | Leave at site three additional sets of filters for site personnel to change each month. | X | | Check electrical wiring and connections. Tighten loose connections. | X | | Check and record amperage across blower motor. | X | | Check tension, condition and alignment of belts. Adjust as necessary. | X | | Lubricate shaft and motor bearing. | X | | Condenser Maintenance (Basic) | | | Check and record amperage across condenser fan motor. | X | | Check electrical wiring and connections. Tighten loose connections. | X | | Clean condensate lines and pans. | X | | Check contactors and starters. | X | | Cooling Maintenance (Spring only-May) | | | Power wash condenser coil(s) and clean evaporator coil(s). | X | | Change all belts. | X | | Annual asset inventory report and analysis. | X | | Heat Maintenance (Fall only-November) | | | Verify pilot ignition-check for proper operation of primary fuel controls and safety | X | | controls. Check and adjust thermostat. Check pump pressure (fuel oil). | | | Check and clean flue. Replace oil filter and nozzle. | X |
| Cycle valves-for automatic valves (check valves)-adjust system pressure/flow to verify that valve is opening and closing properly. For manual valves (Gate/Butterfly)-open and close using handle, wrench, or hand wheel to check operation. Check draft and smoke reading. | X | |---|---| | Check electrical wiring to heating elements, blowers, motors, over-current protective | X | | device, and grounding system. Tighten when necessary. | | | Check the control mechanism for defrosting the coil and for energizing the heat strips | X | | located in the electric furnace evaporator system. | | | Check heater operation through complete cycle or up to 10 minutes. Change air filter. | X | | | | | Check safety devices for proper operation. | X | | Check controls for proper operation. | X | | Clean and remove debris surrounding unit to ensure proper air circulation. | X | | Check and adjust operating temperatures as needed. | X | **Excess Liability coverage may be waived if franchisee carries $1,500,000 General Liability coverage
6. Section 18, Transferability of Interest
In Section 18.2.8, the Transfer Fee shall equal $15,000.00.
7. Supplemental Terms:
The parties acknowledge and agree that the Agreement is hereby supplemented by the inclusion of the following terms and conditions:
22. STORE SPECIFIC ADDITIONAL TERMS AND CONDITIONS
22.1. Construction or Conversion
- 22.1.1.
Source: Item 23 — RECEIPT (FDD pages 68–302)
What This Means (2024 FDD)
According to Aplus's 2024 Franchise Disclosure Document, during the maintenance of Aplus units, several electrical components must be checked and tightened if necessary. For the Air Handling Unit (AHU), the electrical wiring and connections should be inspected and any loose connections tightened. Similarly, for the condenser, the electrical wiring and connections should be checked and tightened.
Additionally, the document specifies that the electrical wiring to heating elements, blowers, motors, over-current protective devices, and the grounding system must be checked and tightened when necessary. For Walk-In Coolers/Walk-In Freezers (WIC/WIF), it is important to ensure that all electrical panels, covers, and equipment panels are secure and to check for proper voltage.
These checks are part of the routine maintenance that Aplus franchisees must perform to ensure the proper functioning and safety of the equipment. Regular inspection and tightening of electrical components can help prevent malfunctions and extend the lifespan of the equipment, which is crucial for maintaining the quality of service and minimizing downtime.